CUTTINGTOOLS / AI
Find equivalents

Cross-brand grade equivalence · brand-neutral

Mitsubishi MC5115: candidate alternatives

How to read this page. These alternatives are compiled from grade comparison charts the manufacturers publish themselves. A direct peer is a grade listed in the same row of a manufacturer comparison chart as MC5115: that is chart comparability, not verified cutting performance and not a drop-in swap. Grades that share only the ISO 513 application position are listed apart, marked not verified. Substrate, cobalt content, coating and edge preparation still differ, and so will tool life and the cutting data you should start from. Validate any swap on a sample part before you change production. Something wrong on this page, or a grade you want removed? research@cuttingtoolsai.eu.

Mitsubishi MC5115 sits at ISO 513 application classes K10, K15 — cast iron. 7 Direct peers are from other makers, listed in the same row of a manufacturer comparison chart. This is chart comparability, not verified cutting performance. 71 more grades share an ISO position only and are not verified.

Alternatives by evidence

Direct peers

Listed in the same row of a manufacturer comparison chart. This is chart comparability, not verified cutting performance.

  • ISCAR IC5010 ISO K10 K15 · 2 charts (Ingersoll, TaeguTec)
  • Kennametal KCK15B ISO K10 K15 · 2 charts (Ingersoll, TaeguTec)
  • Korloy NC6315 ISO K10 · 2 charts (Ingersoll, TaeguTec)
  • Sandvik GC3210 ISO K10 K15 · 3 charts (Ingersoll, TaeguTec, Tungaloy)
  • TaeguTec TT7015 ISO K10 K15 · 2 charts (Ingersoll, TaeguTec)
  • Tungaloy T5115 ISO K10 K15 · 2 charts (Ingersoll, TaeguTec)
  • Walter WKK20S ISO K15 · 2 charts (Ingersoll, TaeguTec)

Same ISO position, not verified

These grades overlap in ISO position only. No manufacturer chart lists them together, and operation and tool material are not verified.

  • Tungaloy NS9530 ISO K10 K15 · not verified
  • Kennametal KC515M ISO K10 · not verified
  • Kennametal KC9325 ISO K10 · not verified
  • Kennametal KT125 ISO K10 · not verified
  • Kyocera CA4515 ISO K10 K15 · not verified

65 more not shown.

More wear-resistant alternatives

Positioned below this grade on the ISO scale (more wear resistance, less toughness). ISO position only, not verified.

  • Sumitomo BN500 ISO K10 · not verified

The free check and the report show each grade with its sources: check MC5115 free.

What this does and does not tell you

An ISO 513 application class says which material group and which range of operations a grade is built for. Two grades sharing a class are built for the same job. They are not identical: substrate grain, cobalt content, coating and edge preparation still differ, and so will tool life and the cutting data you should start from. Treat a candidate here as the shortlist for your own trial, not as a drop-in replacement.

Everything above is derived from the makers' own published application data. Nothing is inferred from price, availability or popularity, and no manufacturer pays to appear here.

Related candidate alternatives

All cross-brand grade candidates

Source-backed grade report · PDF + XLSX

Check Mitsubishi MC5115 against the published chart evidence first. If this grade has a documented candidate, you can order an automatically generated report for one grade (about US$10, charged EUR 9), or add up to two grades (about US$24, charged EUR 22). Currency conversion and tax at checkout may change the USD amount. A chart comparison is not a guaranteed substitute.

Check this grade and see the report →
Cost check · free · brand-neutral

Are you overpaying on your Mitsubishi MC5115 inserts? Paste your insert list and get a cost audit in about 30 seconds: cross-brand candidate alternatives at the same ISO application position, and where you are likely overpaying. No signup, no sales call.

Run a free cost audit → Check your whole grade list · free

After the free check: a sourced PDF + XLSX report from EUR 9 for one grade. How buying works

Ask about your own case

Material, operation, machine — get a grade and a starting cutting data set, grounded in the same reference data.