Cross-brand grade equivalence · brand-neutral
Mitsubishi MP7035: candidate alternatives
How to read this page. These alternatives are compiled from grade comparison charts the manufacturers publish themselves. A direct peer is a grade listed in the same row of a manufacturer comparison chart as MP7035: that is chart comparability, not verified cutting performance and not a drop-in swap. Grades that share only the ISO 513 application position are listed apart, marked not verified. Substrate, cobalt content, coating and edge preparation still differ, and so will tool life and the cutting data you should start from. Validate any swap on a sample part before you change production. Something wrong on this page, or a grade you want removed? research@cuttingtoolsai.eu.
Mitsubishi MP7035 sits at ISO 513 application classes M30, M40 — stainless steel. The manufacturer names a successor grade. 1 Direct peer is from other makers, listed in the same row of a manufacturer comparison chart. This is chart comparability, not verified cutting performance. 60 more grades share an ISO position only and are not verified.
Alternatives by evidence
Manufacturer-stated successor
Named by the manufacturer as the follow-up grade. Same brand, listed apart from other brands.
- Mitsubishi MP7135 ISO M turning · manufacturer source, p.1
Direct peers
Listed in the same row of a manufacturer comparison chart. This is chart comparability, not verified cutting performance.
- Sandvik GC2035 ISO M30 M40 · 1 chart (Ingersoll)
Same ISO position, not verified
These grades overlap in ISO position only. No manufacturer chart lists them together, and operation and tool material are not verified.
- Kennametal KC725M ISO M30 M40 · not verified
- Kyocera PR1535 ISO M30 M40 · not verified · carbide
- MOLDINO JM4160 ISO M30 M40 · not verified
- Sumitomo ACM300 ISO M30 M40 · not verified
- Tungaloy AH6235 ISO M30 M40 · not verified
45 more not shown.
More wear-resistant alternatives
Positioned below this grade on the ISO scale (more wear resistance, less toughness). ISO position only, not verified.
- Kyocera CA6535 ISO M30 · not verified
- ISCAR IC830 ISO M30 · not verified
- Kennametal KCPM30 ISO M30 · not verified
- Kyocera PR1525 ISO M30 · not verified
- NTK DT4 ISO M30 · not verified
5 more not shown.
The free check and the report show each grade with its sources: check MP7035 free.
What this does and does not tell you
An ISO 513 application class says which material group and which range of operations a grade is built for. Two grades sharing a class are built for the same job. They are not identical: substrate grain, cobalt content, coating and edge preparation still differ, and so will tool life and the cutting data you should start from. Treat a candidate here as the shortlist for your own trial, not as a drop-in replacement.
Everything above is derived from the makers' own published application data. Nothing is inferred from price, availability or popularity, and no manufacturer pays to appear here.
Related candidate alternatives
- Mitsubishi US735 M30, M40
- Kyocera PR1725 M30, M35, P20, P25
- Mitsubishi VP30RT M40, P30, P40
- Kyocera PR1525 M20, M30, P20, P30
- MOLDINO GM25 M30, P20, P25, P30
- Kennametal KCU25 K20, M30, M35, P20, P25, S20, S25
All cross-brand grade candidates
Check Mitsubishi MP7035 against the published chart evidence first. If this grade has a documented candidate, you can order an automatically generated report for one grade (about US$10, charged EUR 9), or add up to two grades (about US$24, charged EUR 22). Currency conversion and tax at checkout may change the USD amount. A chart comparison is not a guaranteed substitute.
Check this grade and see the report →Are you overpaying on your Mitsubishi MP7035 inserts? Paste your insert list and get a cost audit in about 30 seconds: cross-brand candidate alternatives at the same ISO application position, and where you are likely overpaying. No signup, no sales call.
After the free check: a sourced PDF + XLSX report from EUR 9 for one grade. How buying works
Ask about your own case
Material, operation, machine — get a grade and a starting cutting data set, grounded in the same reference data.