What is cost per cutting edge?

Cost per cutting edge is the insert price divided by the number of usable edges on that insert. A square insert with four edges at 8 EUR costs 2 EUR per edge, a triangle with three edges at the same price costs 2,67 EUR per edge. It is the fair way to compare inserts of different shapes and prices, instead of comparing sticker price alone.

How do you calculate tool cost per part?

Divide the tool life per edge (in minutes) by the cutting time per part to get parts per edge, then divide the cost per edge by parts per edge. Tool cost per part = (insert price / edges per insert) / (tool life per edge / cutting time per part). This is the number that actually drives your part cost, not the insert's unit price.

Why does a cheaper insert sometimes cost more per part?

Because unit price ignores edge count and tool life. A cheaper insert with fewer edges or shorter tool life can produce fewer parts per edge, so its real cost per part is higher than a pricier insert that lasts longer and cuts faster. Cost per edge and cost per part are the numbers to compare, not the price tag.

What operating hours should I use for an annual tooling-cost projection?

Use your actual annual spindle-on time for that machine or operation, not a generic default. A single eight-hour shift, five days a week, roughly 48 weeks a year, is close to 1,900 to 2,000 hours; two shifts roughly doubles it. If you do not know the real figure, your production or scheduling data will have it, and using the real number is what turns this from a rough estimate into a decision-grade one.

Does this calculator account for machine downtime or scrap cost?

No. This calculator isolates tooling economics only: cost per edge, cost per part, and an annual tooling-cost projection from insert price, edge count, tool life and cycle time. It does not model machine hourly rate, scrap, rework, or changeover time, which belong in a full part-cost model.

MATERIAL CROSS-REFERENCE · P ALLOY STEEL (CRNIMO)

34CrNiMo6 / AISI 4340: one material, every designation.

34CrNiMo6 is the same material your supplier may list as AISI 4340 or JIS SNCM439. This page maps the designations across standards and gives the ISO P-group machining starting point, brand-neutral.

EN · W.-Nr. · AISI/ASTM/UNS · JIS ISO 513 group P Free, no signup

01 · DESIGNATIONS

34CrNiMo6 / AISI 4340 across the standards

System	Designation
EN (EU)	34CrNiMo6
Werkstoffnummer	1.6582
AISI / ASTM / UNS (US)	AISI 4340 (UNS G43400)
JIS (Japan)	SNCM439 (nearest)

Compiled from the public standard designation systems (EN 10027, SAE/AISI, ASTM, UNS, JIS). Entries marked “nearest” are the closest commonly-cited counterpart, not a drop-in equivalent. Always verify against the material certificate.

02 · MACHINING

How 34CrNiMo6 machines

High-strength CrNiMo steel, usually cut quenched and tempered: tough, stringy chips and real heat at the edge. A tough P25-position coated grade and stable chip control beat chasing speed.

ISO group	Starting Vc (coated carbide, turning)	Feed fn
P P · Steel	150–350 m/min · 490–1150 sfm	0.1–0.5 mm/rev · .004–.020 ipr

Group-level starting range from our speeds & feeds guide; convert to RPM with the speeds & feeds calculator. Condition, subgroup and operation shift the number — the material page has the detail: ISO P · Alloy steel (CrNiMo).

03 · FAQ

Common questions

What is the US equivalent of 34CrNiMo6?

34CrNiMo6 (Werkstoffnummer 1.6582) corresponds to AISI 4340 (UNS G43400). In JIS terms the counterpart is SNCM439 (nearest).

Which inserts and cutting data for 34CrNiMo6?

It is an ISO P-group material, so the starting window is 150–350 m/min · 490–1150 sfm at 0.1–0.5 mm/rev · .004–.020 ipr for coated-carbide turning, adjusted for condition and operation. For a grounded, brand-neutral pick — grade, geometry and cutting data across 13 brands — ask the advisor.

Are 34CrNiMo6 and 4340 interchangeable on a drawing?

They designate the same composition under different systems, but the drawing standard governs: certificates, tolerances and delivery-condition requirements differ between standards even for equivalent chemistry. Substitute only with the certificate in hand.

Designation solved. Now the tooling question.

Knowing the material is half the job; picking the grade and cutting data for the operation is the other half. That is what the advisor does, grounded in catalog data and honest when there is no verified match.

Ask the advisor about 34CrNiMo6 → ISO P material guide All material cross-references