Carbide grade · Kyocera · ISO M
Kyocera CA6535
CA6535 is a Kyocera carbide insert grade (Coated), applied in the ISO M area. Its ISO position comes from the manufacturer grade comparison charts in this reference. No manufacturer chart on file lists a direct peer for it. 100 grades from other makers share an ISO position with it. None has been verified. Same position is not the same performance: verify on a sample part before switching.
Grade summary
- Brand
- Kyocera
- Coating / substrate
- Coated
- ISO application area
- M — stainless steel
- ISO position (manufacturer charts)
- M20 · M30
Cross-brand alternatives (manufacturer charts)
Direct peers
Listed in the same row of a manufacturer comparison chart. This is chart comparability, not verified cutting performance.
No manufacturer chart on file lists a direct peer for this grade. Grades at the same ISO position are listed as not verified.
Same ISO position, not verified
These grades overlap in ISO position only. No manufacturer chart lists them together, and operation and tool material are not verified.
- Mitsubishi MC7025 ISO M20 M30 · not verified
- NTK DM4 ISO M20 M30 · not verified
- NTK DT4 ISO M20 M30 · not verified
- NTK ZM3 ISO M20 M30 · not verified
- Seco CP500 ISO M20 M30 · not verified
66 more not shown.
Tougher alternatives
Positioned above this grade on the ISO scale (more toughness, less wear resistance). ISO position only, not verified.
- Kennametal KC5025 ISO M30 · not verified
- Kennametal KCU25 ISO M30 · not verified
- Mitsubishi MS7025 ISO M30 · not verified
- Seco CP600 ISO M30 · not verified
- Sumitomo AC530U ISO M30 · not verified
11 more not shown.
More wear-resistant alternatives
Positioned below this grade on the ISO scale (more wear resistance, less toughness). ISO position only, not verified.
- Sumitomo AC6020M ISO M20 · not verified
- Kennametal KCM25B ISO M20 · not verified
- Walter WSM20S ISO M20 · not verified
- MOLDINO IP100S ISO M20 · not verified
- Sandvik GC2220 ISO M20 · not verified
8 more not shown.
The best-evidenced alternative to Kyocera CA6535 from another maker, with published cutting speeds (sourced, and compared only where both makers publish them for the same conditions), coating and what would decide a switch. Usually in your inbox within 30 minutes.
Check Kyocera CA6535 against the published chart evidence first. If this grade has a documented candidate, you can order an automatically generated report for one grade (about US$10, charged EUR 9), or add up to two grades (about US$24, charged EUR 22). Currency conversion and tax at checkout may change the USD amount. A chart comparison is not a guaranteed substitute.
Check this grade and see the report →Compare CA6535 side by side
Frequently asked questions
What is Kyocera CA6535?
CA6535 is a Kyocera carbide insert grade (Coated), applied in the ISO M area, as positioned in manufacturer grade charts.
Does this cross-reference favour specific brands?
No. Comparable grades appear here only because manufacturer-published comparison charts place them at the same ISO application position. No manufacturer pays for placement, nothing on this page is sponsored, and CuttingToolsAI sells no tools and earns no commission. Placements backed by a single chart are flagged as such, and every comparison ends the same way: verify on a sample part before switching.
Grade charts by brand
Are you overpaying on your CA6535 inserts? Paste your insert list and get a cost audit in about 30 seconds: cross-brand candidate alternatives at the same ISO application position, and where you are likely overpaying. No signup, no sales call.
After the free check: a sourced PDF + XLSX report from EUR 9 for one grade. How buying works
Related grades
Where CA6535 is used: designations and materials