CUTTINGTOOLS / AI
Find equivalents

Carbide grade · ISCAR · ISO P/M/K

ISCAR IC807

IC807 is a ISCAR carbide insert grade (Coated), applied in the ISO P/M/K areas. Its ISO position comes from the manufacturer grade comparison charts in this reference. 2 Direct peers are from other makers, listed in the same row of a manufacturer comparison chart. This is chart comparability, not verified cutting performance. 198 more grades share an ISO position only and are not verified. Same position is not the same performance: verify on a sample part before switching.

Same ISO position in the manufacturer charts, with the source on the full page. Running several grades? Separate them with commas to check the whole list. No signup.

Every maker's AI recommends its own tools. Ours compares all makers and shows the published source behind each answer, or tells you it could not verify.

Grade summary

Brand
ISCAR
Coating / substrate
Coated
ISO application area
P — steel · M — stainless steel · K — cast iron
ISO position (manufacturer charts)
K10 · M15 · P10 · P20

Cross-brand alternatives (manufacturer charts)

Direct peers

Listed in the same row of a manufacturer comparison chart. This is chart comparability, not verified cutting performance.

  • Walter WPP10S ISO P10 · 1 chart (TaeguTec)
  • Sandvik GC1105 ISO M10 · 2 charts (Ingersoll, Tungaloy)

Same ISO position, not verified

These grades overlap in ISO position only. No manufacturer chart lists them together, and operation and tool material are not verified.

  • Mitsubishi NX2525 ISO K10 P10 P20 · not verified · cermet
  • Tungaloy J9530 ISO K10 P10 P20 · not verified
  • Kyocera PV720 ISO P10 P20 · not verified · cermet
  • Kyocera TN620 ISO P10 P20 · not verified · cermet
  • Mitsubishi VP15TF ISO P10 P20 · not verified · carbide

160 more not shown.

Tougher alternatives

Positioned above this grade on the ISO scale (more toughness, less wear resistance). ISO position only, not verified.

25 more not shown.

More wear-resistant alternatives

Positioned below this grade on the ISO scale (more wear resistance, less toughness). ISO position only, not verified.

  • Sandvik GC4305 ISO P10 · not verified
  • Tungaloy T9205 ISO P10 · not verified
  • Kyocera PR1705 ISO P10 · not verified

Check IC807 with your other grades →

Free · engineer's note · by email

The best-evidenced alternative to ISCAR IC807 from another maker, with published cutting speeds (sourced, and compared only where both makers publish them for the same conditions), coating and what would decide a switch. Usually in your inbox within 30 minutes.

Source-backed grade report · PDF + XLSX

Check ISCAR IC807 against the published chart evidence first. If this grade has a documented candidate, you can order an automatically generated report for one grade (about US$10, charged EUR 9), or add up to two grades (about US$24, charged EUR 22). Currency conversion and tax at checkout may change the USD amount. A chart comparison is not a guaranteed substitute.

Check this grade and see the report →

Frequently asked questions

What is ISCAR IC807?

IC807 is a ISCAR carbide insert grade (Coated), applied in the ISO P/M/K areas, as positioned in manufacturer grade charts.

Which grades are direct peers of IC807?

2 grades from other makers are listed in the same row of a manufacturer comparison chart as IC807: Walter WPP10S, Sandvik GC1105. This is chart comparability, not verified cutting performance. Grades that share only the ISO position are listed separately as not verified. Same position is not the same performance: verify on a sample part before switching.

Does this cross-reference favour specific brands?

No. Comparable grades appear here only because manufacturer-published comparison charts place them at the same ISO application position. No manufacturer pays for placement, nothing on this page is sponsored, and CuttingToolsAI sells no tools and earns no commission. Placements backed by a single chart are flagged as such, and every comparison ends the same way: verify on a sample part before switching.

Grade charts by brand

Ask the AI advisor about IC807
Cutting data for your material, when IC807 is the right call versus its equivalents, and what to check before switching — answered with verified reference data plus live search. Edit the question and hit Ask — 3 free answers a day, no account.
Cost check · free · brand-neutral

Are you overpaying on your IC807 inserts? Paste your insert list and get a cost audit in about 30 seconds: cross-brand candidate alternatives at the same ISO application position, and where you are likely overpaying. No signup, no sales call.

Run a free cost audit → Check your whole grade list · free

After the free check: a sourced PDF + XLSX report from EUR 9 for one grade. How buying works

Related grades

Where IC807 is used: designations and materials