Carbide grade · ISCAR · ISO P/K/S
ISCAR IC907
IC907 is a ISCAR carbide insert grade (Coated), applied in the ISO P/K/S areas. Its ISO position comes from the manufacturer grade comparison charts in this reference. 1 Direct peer is from other makers, listed in the same row of a manufacturer comparison chart. This is chart comparability, not verified cutting performance. 197 more grades share an ISO position only and are not verified. Same position is not the same performance: verify on a sample part before switching.
Grade summary
- Brand
- ISCAR
- Coating / substrate
- Coated
- ISO application area
- P — steel · K — cast iron · S — superalloys & titanium
- ISO position (manufacturer charts)
- K10 · P10 · P15 · P20 · S15
Cross-brand alternatives (manufacturer charts)
Direct peers
Listed in the same row of a manufacturer comparison chart. This is chart comparability, not verified cutting performance.
- Sandvik GC1105 ISO S05 S10 · 2 charts (Ingersoll, Tungaloy)
Same ISO position, not verified
These grades overlap in ISO position only. No manufacturer chart lists them together, and operation and tool material are not verified.
- Mitsubishi NX2525 ISO K10 P10 P15 P20 · not verified · cermet
- Kennametal KCU10 ISO K10 P10 S15 · not verified
- Mitsubishi VP25N ISO K10 P10 P15 · not verified
- Tungaloy J9530 ISO K10 P10 P20 · not verified
- Kyocera PV720 ISO P10 P20 · not verified · cermet
156 more not shown.
Tougher alternatives
Positioned above this grade on the ISO scale (more toughness, less wear resistance). ISO position only, not verified.
- Kyocera PR1725 ISO P20 · not verified
- Sandvik GC1125 ISO P20 · not verified
- Kennametal KCP25B ISO P20 · not verified
- Kennametal KCU25 ISO P20 · not verified
- Kyocera CA525 ISO P20 · not verified
28 more not shown.
More wear-resistant alternatives
Positioned below this grade on the ISO scale (more wear resistance, less toughness). ISO position only, not verified.
The best-evidenced alternative to ISCAR IC907 from another maker, with published cutting speeds (sourced, and compared only where both makers publish them for the same conditions), coating and what would decide a switch. Usually in your inbox within 30 minutes.
Check ISCAR IC907 against the published chart evidence first. If this grade has a documented candidate, you can order an automatically generated report for one grade (about US$10, charged EUR 9), or add up to two grades (about US$24, charged EUR 22). Currency conversion and tax at checkout may change the USD amount. A chart comparison is not a guaranteed substitute.
Check this grade and see the report →Compare IC907 side by side
Frequently asked questions
What is ISCAR IC907?
IC907 is a ISCAR carbide insert grade (Coated), applied in the ISO P/K/S areas, as positioned in manufacturer grade charts.
Which grades are direct peers of IC907?
1 grade from another maker is listed in the same row of a manufacturer comparison chart as IC907: Sandvik GC1105. This is chart comparability, not verified cutting performance. Grades that share only the ISO position are listed separately as not verified. Same position is not the same performance: verify on a sample part before switching.
Does this cross-reference favour specific brands?
No. Comparable grades appear here only because manufacturer-published comparison charts place them at the same ISO application position. No manufacturer pays for placement, nothing on this page is sponsored, and CuttingToolsAI sells no tools and earns no commission. Placements backed by a single chart are flagged as such, and every comparison ends the same way: verify on a sample part before switching.
Grade charts by brand
Are you overpaying on your IC907 inserts? Paste your insert list and get a cost audit in about 30 seconds: cross-brand candidate alternatives at the same ISO application position, and where you are likely overpaying. No signup, no sales call.
After the free check: a sourced PDF + XLSX report from EUR 9 for one grade. How buying works
Related grades
Where IC907 is used: designations and materials