CUTTINGTOOLS / AI
Find equivalents

Carbide grade · Kyocera · ISO P/M

Kyocera PR1225

PR1225 is a Kyocera carbide insert grade (Coated), applied in the ISO P/M areas. Its ISO position comes from the manufacturer grade comparison charts in this reference. 2 Direct peers are from other makers, listed in the same row of a manufacturer comparison chart. This is chart comparability, not verified cutting performance. 247 more grades share an ISO position only and are not verified. Same position is not the same performance: verify on a sample part before switching.

Same ISO position in the manufacturer charts, with the source on the full page. Running several grades? Separate them with commas to check the whole list. No signup.

Every maker's AI recommends its own tools. Ours compares all makers and shows the published source behind each answer, or tells you it could not verify.

Grade summary

Brand
Kyocera
Coating / substrate
Coated
ISO application area
P — steel · M — stainless steel
ISO position (manufacturer charts)
M10 · M20 · M30 · M35 · P05 · P10 · P20 · P25

Cross-brand alternatives (manufacturer charts)

Direct peers

Listed in the same row of a manufacturer comparison chart. This is chart comparability, not verified cutting performance.

  • TaeguTec TT9080 ISO M20 P25 · 2+ independent charts (Korloy, TaeguTec)
  • Kennametal KC725M ISO M30 · 1 chart (Tungaloy)

Same ISO position, not verified

These grades overlap in ISO position only. No manufacturer chart lists them together, and operation and tool material are not verified.

  • Sumitomo AC1030U ISO M30 M35 P10 P20 P25 · not verified · carbide
  • Mitsubishi VP15TF ISO M10 M30 M35 P05 P10 P20 · not verified · carbide
  • NTK DM4 ISO M10 M20 M30 P10 P20 · not verified
  • NTK DT4 ISO M20 M30 P05 P10 P20 · not verified
  • Sumitomo ACU2500 ISO M10 M20 P05 P20 · not verified

131 more not shown.

Tougher alternatives

Positioned above this grade on the ISO scale (more toughness, less wear resistance). ISO position only, not verified.

  • Seco TP2501 ISO P20 P25 · not verified · carbide
  • Sumitomo AC8025P ISO P20 P25 · not verified · carbide
  • Mitsubishi MP7130 ISO M30 · not verified
  • ISCAR IC928 ISO M30 · not verified
  • Seco F40M ISO M30 · not verified

59 more not shown.

More wear-resistant alternatives

Positioned below this grade on the ISO scale (more wear resistance, less toughness). ISO position only, not verified.

  • ISCAR IC808 ISO M10 M20 P05 P10 · not verified
  • Tungaloy AH110 ISO M10 P05 · not verified
  • Tungaloy AH710 ISO P05 · not verified
  • Mitsubishi MC7015 ISO M10 M20 · not verified
  • Kennametal K313 ISO M10 M20 · not verified

38 more not shown.

Different tool material

Recorded as a different tool material (for example cermet against carbide). Shown for reference only.

  • Mitsubishi NX2525 ISO P10 P20 · not verified · cermet
  • Sumitomo T1500Z ISO P10 P20 · not verified · cermet
  • Sumitomo T2500Z ISO P20 · not verified · cermet
  • Sumitomo T1500A ISO P10 P20 · not verified · cermet

Check PR1225 with your other grades →

Free · engineer's note · by email

The best-evidenced alternative to Kyocera PR1225 from another maker, with published cutting speeds (sourced, and compared only where both makers publish them for the same conditions), coating and what would decide a switch. Usually in your inbox within 30 minutes.

Source-backed grade report · PDF + XLSX

Check Kyocera PR1225 against the published chart evidence first. If this grade has a documented candidate, you can order an automatically generated report for one grade (about US$10, charged EUR 9), or add up to two grades (about US$24, charged EUR 22). Currency conversion and tax at checkout may change the USD amount. A chart comparison is not a guaranteed substitute.

Check this grade and see the report →

Frequently asked questions

What is Kyocera PR1225?

PR1225 is a Kyocera carbide insert grade (Coated), applied in the ISO P/M areas, as positioned in manufacturer grade charts.

Which grades are direct peers of PR1225?

2 grades from other makers are listed in the same row of a manufacturer comparison chart as PR1225: TaeguTec TT9080, Kennametal KC725M. This is chart comparability, not verified cutting performance. Grades that share only the ISO position are listed separately as not verified. Same position is not the same performance: verify on a sample part before switching.

Does this cross-reference favour specific brands?

No. Comparable grades appear here only because manufacturer-published comparison charts place them at the same ISO application position. No manufacturer pays for placement, nothing on this page is sponsored, and CuttingToolsAI sells no tools and earns no commission. Placements backed by a single chart are flagged as such, and every comparison ends the same way: verify on a sample part before switching.

Grade charts by brand

Ask the AI advisor about PR1225
Cutting data for your material, when PR1225 is the right call versus its equivalents, and what to check before switching — answered with verified reference data plus live search. Edit the question and hit Ask — 3 free answers a day, no account.
Cost check · free · brand-neutral

Are you overpaying on your PR1225 inserts? Paste your insert list and get a cost audit in about 30 seconds: cross-brand candidate alternatives at the same ISO application position, and where you are likely overpaying. No signup, no sales call.

Run a free cost audit → Check your whole grade list · free

After the free check: a sourced PDF + XLSX report from EUR 9 for one grade. How buying works

Related grades

Where PR1225 is used: designations and materials