Carbide grade · Mitsubishi · ISO P/M/K
Mitsubishi UTi20T
UTi20T is a Mitsubishi carbide insert grade (Uncoated), applied in the ISO P/M/K areas. Its ISO position comes from the manufacturer grade comparison charts in this reference. No manufacturer chart on file lists a direct peer for it. 256 grades from other makers share an ISO position with it. None has been verified. Same position is not the same performance: verify on a sample part before switching.
Grade summary
- Brand
- Mitsubishi
- Coating / substrate
- Uncoated
- ISO application area
- P — steel · M — stainless steel · K — cast iron
- ISO position (manufacturer charts)
- K20 · K30 · M20 · M30 · P20 · P30 · P35
Cross-brand alternatives (manufacturer charts)
Direct peers
Listed in the same row of a manufacturer comparison chart. This is chart comparability, not verified cutting performance.
No manufacturer chart on file lists a direct peer for this grade. Grades at the same ISO position are listed as not verified.
Same ISO position, not verified
These grades overlap in ISO position only. No manufacturer chart lists them together, and operation and tool material are not verified.
- Sumitomo ACU2500 ISO K20 K30 M20 P20 P30 · not verified
- Kyocera PR1525 ISO M20 M30 P20 P30 · not verified
- Sumitomo AC1030U ISO K20 M30 P20 P30 · not verified · carbide
- Tungaloy AH120 ISO K20 K30 P20 P30 · not verified
- ISCAR IC908 ISO K20 M30 P20 · not verified
164 more not shown.
Tougher alternatives
Positioned above this grade on the ISO scale (more toughness, less wear resistance). ISO position only, not verified.
- Sumitomo ACP300 ISO P30 · not verified
- Sumitomo ACP3000 ISO P30 · not verified
- Kyocera CA530 ISO P30 P35 · not verified
- MOLDINO IP3000 ISO P30 P35 · not verified
- Sandvik GC4335 ISO P30 P35 · not verified
11 more not shown.
More wear-resistant alternatives
Positioned below this grade on the ISO scale (more wear resistance, less toughness). ISO position only, not verified.
- Kennametal KC9125 ISO P20 · not verified
- MOLDINO CZ25 ISO P20 · not verified
- Tungaloy AT9530 ISO P20 · not verified
- ISCAR IC530N ISO P20 · not verified
- Kennametal KCM25B ISO M20 · not verified
66 more not shown.
The best-evidenced alternative to Mitsubishi UTi20T from another maker, with published cutting speeds (sourced, and compared only where both makers publish them for the same conditions), coating and what would decide a switch. Usually in your inbox within 30 minutes.
Check Mitsubishi UTi20T against the published chart evidence first. If this grade has a documented candidate, you can order an automatically generated report for one grade (about US$10, charged EUR 9), or add up to two grades (about US$24, charged EUR 22). Currency conversion and tax at checkout may change the USD amount. A chart comparison is not a guaranteed substitute.
Check this grade and see the report →Compare UTi20T side by side
Frequently asked questions
What is Mitsubishi UTi20T?
UTi20T is a Mitsubishi carbide insert grade (Uncoated), applied in the ISO P/M/K areas, as positioned in manufacturer grade charts.
Does this cross-reference favour specific brands?
No. Comparable grades appear here only because manufacturer-published comparison charts place them at the same ISO application position. No manufacturer pays for placement, nothing on this page is sponsored, and CuttingToolsAI sells no tools and earns no commission. Placements backed by a single chart are flagged as such, and every comparison ends the same way: verify on a sample part before switching.
Grade charts by brand
Are you overpaying on your UTi20T inserts? Paste your insert list and get a cost audit in about 30 seconds: cross-brand candidate alternatives at the same ISO application position, and where you are likely overpaying. No signup, no sales call.
After the free check: a sourced PDF + XLSX report from EUR 9 for one grade. How buying works
Related grades
Where UTI20T is used: designations and materials