Carbide grade · Mitsubishi · ISO P
Mitsubishi VP45N
VP45N is a Mitsubishi carbide insert grade (Coated), applied in the ISO P area. Its ISO position comes from the manufacturer grade comparison charts in this reference. The manufacturer names a successor grade. No manufacturer chart on file lists a direct peer for it. 104 grades from other makers share an ISO position with it. None has been verified. Same position is not the same performance: verify on a sample part before switching.
Newer grade listed by the maker
Mitsubishi lists Mitsubishi MP3025 against VP45N in its own documents. That is a maker-stated successor, not a discontinuation notice: see the source and what to check before switching →
Grade summary
- Brand
- Mitsubishi
- Coating / substrate
- Coated
- ISO application area
- P — steel
- ISO position (manufacturer charts)
- P25 · P30
Cross-brand alternatives (manufacturer charts)
Manufacturer-stated successor
Named by the manufacturer as the follow-up grade. Same brand, listed apart from other brands.
- Mitsubishi MP3025 ISO P/M (PVD) · manufacturer source, p.1
Direct peers
Listed in the same row of a manufacturer comparison chart. This is chart comparability, not verified cutting performance.
No manufacturer chart on file lists a direct peer for this grade. Grades at the same ISO position are listed as not verified.
Same ISO position, not verified
These grades overlap in ISO position only. No manufacturer chart lists them together, and operation and tool material are not verified.
- ISCAR IC8350 ISO P30 · not verified
- Kyocera PV730 ISO P30 · not verified · cermet
- Kennametal KC530M ISO P30 · not verified
- Kennametal KCPK30 ISO P30 · not verified
- Kyocera PR1230 ISO P30 · not verified
83 more not shown.
Tougher alternatives
Positioned above this grade on the ISO scale (more toughness, less wear resistance). ISO position only, not verified.
- Sumitomo ACP300 ISO P30 · not verified
- Sumitomo ACP3000 ISO P30 · not verified
- ISCAR IC28 ISO P30 · not verified
- ISCAR IC830 ISO P30 · not verified
- ISCAR IC928 ISO P30 · not verified
10 more not shown.
More wear-resistant alternatives
Positioned below this grade on the ISO scale (more wear resistance, less toughness). ISO position only, not verified.
- Kyocera PR1225 ISO P25 · not verified · carbide
The best-evidenced alternative to Mitsubishi VP45N from another maker, with published cutting speeds (sourced, and compared only where both makers publish them for the same conditions), coating and what would decide a switch. Usually in your inbox within 30 minutes.
Check Mitsubishi VP45N against the published chart evidence first. If this grade has a documented candidate, you can order an automatically generated report for one grade (about US$10, charged EUR 9), or add up to two grades (about US$24, charged EUR 22). Currency conversion and tax at checkout may change the USD amount. A chart comparison is not a guaranteed substitute.
Check this grade and see the report →Compare VP45N side by side
Frequently asked questions
What is Mitsubishi VP45N?
VP45N is a Mitsubishi carbide insert grade (Coated), applied in the ISO P area, as positioned in manufacturer grade charts.
Does this cross-reference favour specific brands?
No. Comparable grades appear here only because manufacturer-published comparison charts place them at the same ISO application position. No manufacturer pays for placement, nothing on this page is sponsored, and CuttingToolsAI sells no tools and earns no commission. Placements backed by a single chart are flagged as such, and every comparison ends the same way: verify on a sample part before switching.
Grade charts by brand
Are you overpaying on your VP45N inserts? Paste your insert list and get a cost audit in about 30 seconds: cross-brand candidate alternatives at the same ISO application position, and where you are likely overpaying. No signup, no sales call.
After the free check: a sourced PDF + XLSX report from EUR 9 for one grade. How buying works
Related grades
Where VP45N is used: designations and materials