Carbide grade · Tungaloy · ISO P/K
Tungaloy J9530
J9530 is a Tungaloy carbide insert grade (Coated), applied in the ISO P/K areas. Its ISO position comes from the manufacturer grade comparison charts in this reference. No manufacturer chart on file lists a direct peer for it. 196 grades from other makers share an ISO position with it. None has been verified. Same position is not the same performance: verify on a sample part before switching.
Grade summary
- Brand
- Tungaloy
- Coating / substrate
- Coated
- ISO application area
- P — steel · K — cast iron
- ISO position (manufacturer charts)
- K10 · K15 · P10 · P20
Cross-brand alternatives (manufacturer charts)
Direct peers
Listed in the same row of a manufacturer comparison chart. This is chart comparability, not verified cutting performance.
No manufacturer chart on file lists a direct peer for this grade. Grades at the same ISO position are listed as not verified.
Same ISO position, not verified
These grades overlap in ISO position only. No manufacturer chart lists them together, and operation and tool material are not verified.
- Mitsubishi NX2525 ISO K10 P10 P20 · not verified · cermet
- ISCAR IC5010 ISO K10 K15 · not verified
- Kyocera PV720 ISO P10 P20 · not verified · cermet
- Kyocera TN620 ISO P10 P20 · not verified · cermet
- Mitsubishi VP15TF ISO P10 P20 · not verified · carbide
151 more not shown.
Tougher alternatives
Positioned above this grade on the ISO scale (more toughness, less wear resistance). ISO position only, not verified.
- Sumitomo T2500Z ISO P20 · not verified · cermet
- Kyocera PR1725 ISO P20 · not verified
- ISCAR IC8250 ISO P20 · not verified
- ISCAR IC908 ISO P20 · not verified
- Kennametal KCP25B ISO P20 · not verified
28 more not shown.
More wear-resistant alternatives
Positioned below this grade on the ISO scale (more wear resistance, less toughness). ISO position only, not verified.
- Mitsubishi MB5015 ISO K10 · not verified
- Mitsubishi MB710 ISO K10 · not verified
- Sumitomo BN500 ISO K10 · not verified
- ISCAR IC808 ISO P10 · not verified
- ISCAR IC9015 ISO P10 · not verified
2 more not shown.
The best-evidenced alternative to Tungaloy J9530 from another maker, with published cutting speeds (sourced, and compared only where both makers publish them for the same conditions), coating and what would decide a switch. Usually in your inbox within 30 minutes.
Check Tungaloy J9530 against the published chart evidence first. If this grade has a documented candidate, you can order an automatically generated report for one grade (about US$10, charged EUR 9), or add up to two grades (about US$24, charged EUR 22). Currency conversion and tax at checkout may change the USD amount. A chart comparison is not a guaranteed substitute.
Check this grade and see the report →Compare J9530 side by side
Frequently asked questions
What is Tungaloy J9530?
J9530 is a Tungaloy carbide insert grade (Coated), applied in the ISO P/K areas, as positioned in manufacturer grade charts.
Does this cross-reference favour specific brands?
No. Comparable grades appear here only because manufacturer-published comparison charts place them at the same ISO application position. No manufacturer pays for placement, nothing on this page is sponsored, and CuttingToolsAI sells no tools and earns no commission. Placements backed by a single chart are flagged as such, and every comparison ends the same way: verify on a sample part before switching.
Grade charts by brand
Are you overpaying on your J9530 inserts? Paste your insert list and get a cost audit in about 30 seconds: cross-brand candidate alternatives at the same ISO application position, and where you are likely overpaying. No signup, no sales call.
After the free check: a sourced PDF + XLSX report from EUR 9 for one grade. How buying works
Related grades
Where J9530 is used: designations and materials