CUTTINGTOOLS / AI
Find equivalents

Carbide grade · Tungaloy · ISO K

Tungaloy T515

T515 is a Tungaloy carbide insert grade (Coated), applied in the ISO K area. Its ISO position comes from the manufacturer grade comparison charts in this reference. 1 Direct peer is from other makers, listed in the same row of a manufacturer comparison chart. This is chart comparability, not verified cutting performance. 117 more grades share an ISO position only and are not verified. Same position is not the same performance: verify on a sample part before switching.

Same ISO position in the manufacturer charts, with the source on the full page. Running several grades? Separate them with commas to check the whole list. No signup.

Every maker's AI recommends its own tools. Ours compares all makers and shows the published source behind each answer, or tells you it could not verify.

Grade summary

Brand
Tungaloy
Coating / substrate
Coated
ISO application area
K — cast iron
ISO position (manufacturer charts)
K10 · K15 · K20

Cross-brand alternatives (manufacturer charts)

Direct peers

Listed in the same row of a manufacturer comparison chart. This is chart comparability, not verified cutting performance.

  • Sandvik GC3210 ISO K10 K15 · 1 chart (Ingersoll)

Same ISO position, not verified

These grades overlap in ISO position only. No manufacturer chart lists them together, and operation and tool material are not verified.

  • ISCAR IC5010 ISO K10 K15 · not verified
  • Kyocera PR1210 ISO K10 K20 · not verified
  • Sandvik GC1020 ISO K10 K20 · not verified
  • Sumitomo ACK3000 ISO K10 K20 · not verified
  • Sumitomo ACU2500 ISO K10 K20 · not verified

93 more not shown.

Tougher alternatives

Positioned above this grade on the ISO scale (more toughness, less wear resistance). ISO position only, not verified.

4 more not shown.

More wear-resistant alternatives

Positioned below this grade on the ISO scale (more wear resistance, less toughness). ISO position only, not verified.

  • ISCAR IC5005 ISO K10 · not verified
  • Mitsubishi MP8010 ISO K10 · not verified
  • NTK CP1 ISO K10 · not verified
  • Sandvik GC1010 ISO K10 · not verified
  • Sumitomo AC4010K ISO K10 · not verified

5 more not shown.

Check T515 with your other grades →

Free · engineer's note · by email

The best-evidenced alternative to Tungaloy T515 from another maker, with published cutting speeds (sourced, and compared only where both makers publish them for the same conditions), coating and what would decide a switch. Usually in your inbox within 30 minutes.

Source-backed grade report · PDF + XLSX

Check Tungaloy T515 against the published chart evidence first. If this grade has a documented candidate, you can order an automatically generated report for one grade (about US$10, charged EUR 9), or add up to two grades (about US$24, charged EUR 22). Currency conversion and tax at checkout may change the USD amount. A chart comparison is not a guaranteed substitute.

Check this grade and see the report →

Frequently asked questions

What is Tungaloy T515?

T515 is a Tungaloy carbide insert grade (Coated), applied in the ISO K area, as positioned in manufacturer grade charts.

Which grades are direct peers of T515?

1 grade from another maker is listed in the same row of a manufacturer comparison chart as T515: Sandvik GC3210. This is chart comparability, not verified cutting performance. Grades that share only the ISO position are listed separately as not verified. Same position is not the same performance: verify on a sample part before switching.

Does this cross-reference favour specific brands?

No. Comparable grades appear here only because manufacturer-published comparison charts place them at the same ISO application position. No manufacturer pays for placement, nothing on this page is sponsored, and CuttingToolsAI sells no tools and earns no commission. Placements backed by a single chart are flagged as such, and every comparison ends the same way: verify on a sample part before switching.

Grade charts by brand

Ask the AI advisor about T515
Cutting data for your material, when T515 is the right call versus its equivalents, and what to check before switching — answered with verified reference data plus live search. Edit the question and hit Ask — 3 free answers a day, no account.
Cost check · free · brand-neutral

Are you overpaying on your T515 inserts? Paste your insert list and get a cost audit in about 30 seconds: cross-brand candidate alternatives at the same ISO application position, and where you are likely overpaying. No signup, no sales call.

Run a free cost audit → Check your whole grade list · free

After the free check: a sourced PDF + XLSX report from EUR 9 for one grade. How buying works

Related grades

Where T515 is used: designations and materials