CUTTINGTOOLS / AI
Find equivalents

Carbide grade · Mitsubishi · ISO P/K/S

Mitsubishi VP20RT

VP20RT is a Mitsubishi carbide insert grade (Coated), applied in the ISO P/K/S areas. Its ISO position comes from the manufacturer grade comparison charts in this reference. 1 Direct peer is from other makers, listed in the same row of a manufacturer comparison chart. This is chart comparability, not verified cutting performance. 205 more grades share an ISO position only and are not verified. Same position is not the same performance: verify on a sample part before switching.

Same ISO position in the manufacturer charts, with the source on the full page. Running several grades? Separate them with commas to check the whole list. No signup.

Every maker's AI recommends its own tools. Ours compares all makers and shows the published source behind each answer, or tells you it could not verify.

Grade summary

Brand
Mitsubishi
Coating / substrate
Coated
ISO application area
P — steel · K — cast iron · S — superalloys & titanium
ISO position (manufacturer charts)
K20 · K30 · P20 · P30 · P35 · S30

Cross-brand alternatives (manufacturer charts)

Direct peers

Listed in the same row of a manufacturer comparison chart. This is chart comparability, not verified cutting performance.

  • Sandvik GC1125 ISO P20 P30 · 2 charts (Ingersoll, Tungaloy)

Same ISO position, not verified

These grades overlap in ISO position only. No manufacturer chart lists them together, and operation and tool material are not verified.

  • Sumitomo ACU2500 ISO K20 K30 P20 P30 · not verified
  • Tungaloy AH120 ISO K20 K30 P20 P30 · not verified
  • Sumitomo AC1030U ISO K20 P20 P30 · not verified · carbide
  • ISCAR IC8350 ISO P30 P35 · not verified
  • Sumitomo T2500Z ISO P20 P30 · not verified · cermet

118 more not shown.

Tougher alternatives

Positioned above this grade on the ISO scale (more toughness, less wear resistance). ISO position only, not verified.

  • Sumitomo ACP300 ISO P30 · not verified
  • Sumitomo ACP3000 ISO P30 · not verified
  • ISCAR IC28 ISO P30 · not verified
  • ISCAR IC830 ISO P30 · not verified
  • ISCAR IC928 ISO P30 · not verified

11 more not shown.

More wear-resistant alternatives

Positioned below this grade on the ISO scale (more wear resistance, less toughness). ISO position only, not verified.

  • Kennametal KC9125 ISO P20 · not verified
  • MOLDINO CZ25 ISO P20 · not verified
  • Tungaloy AT9530 ISO P20 · not verified
  • ISCAR IC530N ISO P20 · not verified
  • Kennametal KT5020 ISO P20 · not verified

61 more not shown.

Check VP20RT with your other grades →

Free · engineer's note · by email

The best-evidenced alternative to Mitsubishi VP20RT from another maker, with published cutting speeds (sourced, and compared only where both makers publish them for the same conditions), coating and what would decide a switch. Usually in your inbox within 30 minutes.

Source-backed grade report · PDF + XLSX

Check Mitsubishi VP20RT against the published chart evidence first. If this grade has a documented candidate, you can order an automatically generated report for one grade (about US$10, charged EUR 9), or add up to two grades (about US$24, charged EUR 22). Currency conversion and tax at checkout may change the USD amount. A chart comparison is not a guaranteed substitute.

Check this grade and see the report →

Frequently asked questions

What is Mitsubishi VP20RT?

VP20RT is a Mitsubishi carbide insert grade (Coated), applied in the ISO P/K/S areas, as positioned in manufacturer grade charts.

Which grades are direct peers of VP20RT?

1 grade from another maker is listed in the same row of a manufacturer comparison chart as VP20RT: Sandvik GC1125. This is chart comparability, not verified cutting performance. Grades that share only the ISO position are listed separately as not verified. Same position is not the same performance: verify on a sample part before switching.

Does this cross-reference favour specific brands?

No. Comparable grades appear here only because manufacturer-published comparison charts place them at the same ISO application position. No manufacturer pays for placement, nothing on this page is sponsored, and CuttingToolsAI sells no tools and earns no commission. Placements backed by a single chart are flagged as such, and every comparison ends the same way: verify on a sample part before switching.

Grade charts by brand

Ask the AI advisor about VP20RT
Cutting data for your material, when VP20RT is the right call versus its equivalents, and what to check before switching — answered with verified reference data plus live search. Edit the question and hit Ask — 3 free answers a day, no account.
Cost check · free · brand-neutral

Are you overpaying on your VP20RT inserts? Paste your insert list and get a cost audit in about 30 seconds: cross-brand candidate alternatives at the same ISO application position, and where you are likely overpaying. No signup, no sales call.

Run a free cost audit → Check your whole grade list · free

After the free check: a sourced PDF + XLSX report from EUR 9 for one grade. How buying works

Related grades

Where VP20RT is used: designations and materials