Carbide grade · Sandvik · ISO K
Sandvik GC3210
GC3210 is a Sandvik carbide insert grade (Coated), applied in the ISO K area. Its ISO position comes from the manufacturer grade comparison charts in this reference. 18 Direct peers are from other makers, listed in the same row of a manufacturer comparison chart. This is chart comparability, not verified cutting performance. 81 more grades share an ISO position only and are not verified. Same position is not the same performance: verify on a sample part before switching.
Grade summary
- Brand
- Sandvik
- Coating / substrate
- Coated
- ISO application area
- K — cast iron
- ISO position (manufacturer charts)
- K05 · K10 · K15
Cross-brand alternatives (manufacturer charts)
Direct peers
Listed in the same row of a manufacturer comparison chart. This is chart comparability, not verified cutting performance.
- ISCAR IC5010 ISO K10 K15 · 2+ independent charts (Ingersoll, TaeguTec, Tungaloy)
- Kennametal KC9325 ISO K10 · 3 charts (Ingersoll, TaeguTec, Tungaloy)
- TaeguTec TT7310 ISO K10 · 3 charts (Ingersoll, TaeguTec, Tungaloy)
- Korloy NC6210 ISO K10 · 2 charts (Ingersoll, TaeguTec)
- Korloy NC6315 ISO K10 · 2 charts (Ingersoll, TaeguTec)
- Seco TK2000 ISO K10 · 2 charts (Ingersoll, TaeguTec)
- Seco TK2001 ISO K10 · 2 charts (Ingersoll, TaeguTec)
- Kennametal KCK15 ISO K10 · 3 charts (Ingersoll, TaeguTec, Tungaloy)
- Ceratizit CTCK110 ISO K10 · 1 chart (Tungaloy)
- Kennametal KCK15B ISO K10 K15 · 3 charts (Ingersoll, TaeguTec, Tungaloy)
- Mitsubishi MC5115 ISO K10 K15 · 3 charts (Ingersoll, TaeguTec, Tungaloy)
- Mitsubishi UC5115 ISO K10 K15 · 3 charts (Ingersoll, TaeguTec, Tungaloy)
- TaeguTec TT7015 ISO K10 K15 · 3 charts (Ingersoll, TaeguTec, Tungaloy)
- Tungaloy T5115 ISO K10 K15 · 1 chart (Ingersoll)
- Tungaloy T515 ISO K10 K15 · 1 chart (Ingersoll)
- Walter WAK20 ISO K15 · 2 charts (Ingersoll, TaeguTec)
- Walter WKK20S ISO K15 · 2 charts (Ingersoll, TaeguTec)
- Ceratizit CTC3110 ISO position on file · 1 chart (Tungaloy)
Same ISO position, not verified
These grades overlap in ISO position only. No manufacturer chart lists them together, and operation and tool material are not verified.
- Mitsubishi MP8010 ISO K05 K10 · not verified
- Sumitomo ACK3000 ISO K05 K10 · not verified
- Tungaloy NS9530 ISO K10 K15 · not verified
- Mitsubishi NX2525 ISO K10 · not verified · cermet
- Kennametal KC515M ISO K10 · not verified
73 more not shown.
Tougher alternatives
Positioned above this grade on the ISO scale (more toughness, less wear resistance). ISO position only, not verified.
More wear-resistant alternatives
Positioned below this grade on the ISO scale (more wear resistance, less toughness). ISO position only, not verified.
- Mitsubishi HTi05T ISO K05 · not verified
The best-evidenced alternative to Sandvik GC3210 from another maker, with published cutting speeds (sourced, and compared only where both makers publish them for the same conditions), coating and what would decide a switch. Usually in your inbox within 30 minutes.
Check Sandvik GC3210 against the published chart evidence first. If this grade has a documented candidate, you can order an automatically generated report for one grade (about US$10, charged EUR 9), or add up to two grades (about US$24, charged EUR 22). Currency conversion and tax at checkout may change the USD amount. A chart comparison is not a guaranteed substitute.
Check this grade and see the report →Compare GC3210 side by side
Frequently asked questions
What is Sandvik GC3210?
GC3210 is a Sandvik carbide insert grade (Coated), applied in the ISO K area, as positioned in manufacturer grade charts.
Which grades are direct peers of GC3210?
18 grades from other makers are listed in the same row of a manufacturer comparison chart as GC3210: ISCAR IC5010, Kennametal KC9325, TaeguTec TT7310, Korloy NC6210, Korloy NC6315, Seco TK2000, Seco TK2001, Kennametal KCK15, Ceratizit CTCK110, Kennametal KCK15B, Mitsubishi MC5115, Mitsubishi UC5115, TaeguTec TT7015, Tungaloy T5115, Tungaloy T515, Walter WAK20, Walter WKK20S, Ceratizit CTC3110. This is chart comparability, not verified cutting performance. Grades that share only the ISO position are listed separately as not verified. Same position is not the same performance: verify on a sample part before switching.
Does this cross-reference favour specific brands?
No. Comparable grades appear here only because manufacturer-published comparison charts place them at the same ISO application position. No manufacturer pays for placement, nothing on this page is sponsored, and CuttingToolsAI sells no tools and earns no commission. Placements backed by a single chart are flagged as such, and every comparison ends the same way: verify on a sample part before switching.
Grade charts by brand
Are you overpaying on your GC3210 inserts? Paste your insert list and get a cost audit in about 30 seconds: cross-brand candidate alternatives at the same ISO application position, and where you are likely overpaying. No signup, no sales call.
After the free check: a sourced PDF + XLSX report from EUR 9 for one grade. How buying works
Related grades
Where GC3210 is used: designations and materials