CUTTINGTOOLS / AI
Find equivalents

Carbide grade · Sandvik · ISO K

Sandvik GC3040

GC3040 is a Sandvik carbide insert grade (CVD), applied in the ISO K area. In this cross-reference it appears on 1 insert designation; the same insert geometry is also made by ISCAR. No manufacturer chart on file lists a direct peer for it. 68 grades from other makers share an ISO position with it. None has been verified. Same position is not the same performance: verify on a sample part before switching.

Same ISO position in the manufacturer charts, with the source on the full page. Running several grades? Separate them with commas to check the whole list. No signup.

Every maker's AI recommends its own tools. Ours compares all makers and shows the published source behind each answer, or tells you it could not verify.

Grade summary

Brand
Sandvik
Coating / substrate
CVD
ISO application area
K — cast iron
Application range (catalog)
K20
Used in
1 insert designation in this reference

Cross-brand alternatives (manufacturer charts)

Direct peers

Listed in the same row of a manufacturer comparison chart. This is chart comparability, not verified cutting performance.

No manufacturer chart on file lists a direct peer for this grade. Grades at the same ISO position are listed as not verified.

Same ISO position, not verified

These grades overlap in ISO position only. No manufacturer chart lists them together, and operation and tool material are not verified.

63 more not shown.

Check GC3040 with your other grades →

Free · engineer's note · by email

The best-evidenced alternative to Sandvik GC3040 from another maker, with published cutting speeds (sourced, and compared only where both makers publish them for the same conditions), coating and what would decide a switch. Usually in your inbox within 30 minutes.

Source-backed grade report · PDF + XLSX

Check Sandvik GC3040 against the published chart evidence first. If this grade has a documented candidate, you can order an automatically generated report for one grade (about US$10, charged EUR 9), or add up to two grades (about US$24, charged EUR 22). Currency conversion and tax at checkout may change the USD amount. A chart comparison is not a guaranteed substitute.

Check this grade and see the report →

Same insert geometry, other brands

These makers produce the same insert designation in their own grade. Shared geometry is not a grade equivalence.

BrandGradeCoatingShared designations
ISCAR IC908 PVD TiAlN WCMX050308

Insert designations using GC3040

DesignationGeometryCatalog codeApplication
WCMX050308 80° Trigon · 0° clearance · 5mm IC · indexable drill insert WCMX 05 03 08R-53 GC3040 K20

Frequently asked questions

What is Sandvik GC3040?

GC3040 is a Sandvik carbide insert grade (CVD), applied in the ISO K area, used in 1 insert designation in this reference.

Does this cross-reference favour specific brands?

No. Comparable grades appear here only because manufacturer-published comparison charts place them at the same ISO application position. No manufacturer pays for placement, nothing on this page is sponsored, and CuttingToolsAI sells no tools and earns no commission. Placements backed by a single chart are flagged as such, and every comparison ends the same way: verify on a sample part before switching.

Grade charts by brand

Ask the AI advisor about GC3040
Cutting data for your material, when GC3040 is the right call versus its equivalents, and what to check before switching — answered with verified reference data plus live search. Edit the question and hit Ask — 3 free answers a day, no account.
Cost check · free · brand-neutral

Are you overpaying on your GC3040 inserts? Paste your insert list and get a cost audit in about 30 seconds: cross-brand candidate alternatives at the same ISO application position, and where you are likely overpaying. No signup, no sales call.

Run a free cost audit → Check your whole grade list · free

After the free check: a sourced PDF + XLSX report from EUR 9 for one grade. How buying works

Related grades

Where GC3040 is used: designations and materials