CUTTINGTOOLS / AI
Find equivalents

Carbide grade · Sandvik · ISO P

Sandvik GC4325

GC4325 is a Sandvik carbide insert grade (Inveio® CVD Al₂O₃), applied in the ISO P area. In this cross-reference it appears on 10 insert designations; the same insert geometry is also made by ISCAR, Kennametal, Mitsubishi, Seco, Tungaloy, Walter. The manufacturer names a successor grade. 17 Direct peers are from other makers, listed in the same row of a manufacturer comparison chart. This is chart comparability, not verified cutting performance. 145 more grades share an ISO position only and are not verified. Same position is not the same performance: verify on a sample part before switching.

Candidate cross-brand alternatives for Sandvik GC4325, with the manufacturer charts behind each one: Sandvik GC4325 equivalents.

Same ISO position in the manufacturer charts, with the source on the full page. Running several grades? Separate them with commas to check the whole list. No signup.

Every maker's AI recommends its own tools. Ours compares all makers and shows the published source behind each answer, or tells you it could not verify.

Newer grade listed by the maker

Sandvik lists Sandvik GC4425 against GC4325 in its own documents. That is a maker-stated successor, not a discontinuation notice: see the source and what to check before switching →

Grade summary

Brand
Sandvik
Coating / substrate
Inveio® CVD Al₂O₃
ISO application area
P — steel
Application range (catalog)
P20–P30
Used in
10 insert designations in this reference

Cross-brand alternatives (manufacturer charts)

Manufacturer-stated successor

Named by the manufacturer as the follow-up grade. Same brand, listed apart from other brands.

Direct peers

Listed in the same row of a manufacturer comparison chart. This is chart comparability, not verified cutting performance.

  • ISCAR IC8250 ISO P20 P25 · 3 charts (Ingersoll, TaeguTec, Tungaloy)
  • Kennametal KCP25B ISO P20 P25 · 3 charts (Ingersoll, TaeguTec, Tungaloy)
  • TaeguTec TT8125B ISO P20 P25 · 3 charts (Ingersoll, TaeguTec, Tungaloy)
  • Walter WPP20G ISO P20 P25 · 3 charts (Ingersoll, TaeguTec, Tungaloy)
  • Walter WPP20S ISO P20 P25 · 3 charts (Ingersoll, TaeguTec, Tungaloy)
  • Mitsubishi MC6025 ISO P20 P25 · 2 charts (Ingersoll, Tungaloy)
  • Seco TP2501 ISO P20 P25 · 2 charts (Ingersoll, Tungaloy) · carbide
  • Tungaloy T9225 ISO P20 P25 · 2 charts (Ingersoll, Tungaloy)
  • Seco TP2500 ISO P20 P25 · 2 charts (Ingersoll, Tungaloy)
  • Kennametal KC9125 ISO P20 · 3 charts (Ingersoll, TaeguTec, Tungaloy)
  • TaeguTec TT5100 ISO P30 · 3 charts (Ingersoll, TaeguTec, Tungaloy)
  • Seco TP2000 ISO P20 · 2 charts (Ingersoll, Tungaloy)
  • Tungaloy T9025 ISO P20 · 2 charts (Ingersoll, Tungaloy)
  • Kennametal KCP25 ISO P20 · 3 charts (Ingersoll, TaeguTec, Tungaloy)
  • Ceratizit CTCP115 ISO P20 · 1 chart (Tungaloy)
  • Ceratizit CTCP125 ISO P20 · 1 chart (Tungaloy)
  • ISCAR IC9250 ISO position on file · 3 charts (Ingersoll, TaeguTec, Tungaloy)

Same ISO position, not verified

These grades overlap in ISO position only. No manufacturer chart lists them together, and operation and tool material are not verified.

  • Sumitomo AC1030U ISO P20 P25 P30 · not verified · carbide
  • Mitsubishi VP15TF ISO P20 P30 · not verified · carbide
  • Sumitomo T2500Z ISO P20 P30 · not verified · cermet
  • Tungaloy NS9530 ISO P20 P30 · not verified
  • ISCAR IC30N ISO P20 P30 · not verified

95 more not shown.

Tougher alternatives

Positioned above this grade on the ISO scale (more toughness, less wear resistance). ISO position only, not verified.

  • ISCAR IC8350 ISO P30 · not verified
  • Kyocera PR1535 ISO P30 · not verified · carbide
  • Tungaloy UX30 ISO P30 · not verified
  • ISCAR IC50M ISO P30 · not verified
  • Kennametal KCP30B ISO P30 · not verified

20 more not shown.

More wear-resistant alternatives

Positioned below this grade on the ISO scale (more wear resistance, less toughness). ISO position only, not verified.

  • Kyocera PV720 ISO P20 · not verified · cermet
  • Kyocera TN620 ISO P20 · not verified · cermet
  • Mitsubishi NX2525 ISO P20 · not verified · cermet
  • NTK DM4 ISO P20 · not verified
  • Sumitomo T1500A ISO P20 · not verified · cermet

15 more not shown.

Check GC4325 with your other grades →

Free · engineer's note · by email

The best-evidenced alternative to Sandvik GC4325 from another maker, with published cutting speeds (sourced, and compared only where both makers publish them for the same conditions), coating and what would decide a switch. Usually in your inbox within 30 minutes.

Source-backed grade report · PDF + XLSX

Check Sandvik GC4325 against the published chart evidence first. If this grade has a documented candidate, you can order an automatically generated report for one grade (about US$10, charged EUR 9), or add up to two grades (about US$24, charged EUR 22). Currency conversion and tax at checkout may change the USD amount. A chart comparison is not a guaranteed substitute.

Check this grade and see the report →

Insert designations using GC4325

DesignationGeometryCatalog codeApplication
CNMG120404 80° Diamond · 0° clearance · 12mm IC · 0.4mm Rε (finishing) CNMG120404 GC4325 P20–P30
CNMG120408 80° Diamond · 0° clearance · 12mm IC · 0.8mm Rε CNMG 12 04 08-PM 4325 P20–P30
DNMG150604 55° Diamond · 0° clearance · 15mm IC · 0.4mm Rε (finishing) DNMG150604 GC4325 P20–P30
DNMG150608 55° Diamond · 0° clearance · 15mm IC · 0.8mm Rε DNMG 15 06 08-PM 4325 P20–P30
DNMG150612 55° Diamond · 0° clearance · 15mm IC · 1.2mm Rε (roughing) DNMG150612 GC4325 P20–P30
SNMG120404 90° Square · 0° clearance · 12mm IC · 0.4mm Rε (finishing) SNMG120404 GC4325 P20–P30
SNMG120408 90° Square · 0° clearance · 12mm IC · 0.8mm Rε SNMG 12 04 08-PR 4325 P20–P30
SNMG120412 90° Square · 0° clearance · 12mm IC · 1.2mm Rε (roughing) SNMG120412 GC4325 P20–P30
TNMG160408 60° Triangle · 0° clearance · 16mm IC · 0.8mm Rε TNMG 16 04 08-PR 4325 P20–P30
TNMG160412 60° Triangle · 0° clearance · 16mm IC · 1.2mm Rε (roughing) TNMG160412 GC4325 P20–P30

Frequently asked questions

What is Sandvik GC4325?

GC4325 is a Sandvik carbide insert grade (Inveio® CVD Al₂O₃), applied in the ISO P area, used in 10 insert designations in this reference.

Which grades are direct peers of GC4325?

17 grades from other makers are listed in the same row of a manufacturer comparison chart as GC4325: ISCAR IC8250, Kennametal KCP25B, TaeguTec TT8125B, Walter WPP20G, Walter WPP20S, Mitsubishi MC6025, Seco TP2501, Tungaloy T9225, Seco TP2500, Kennametal KC9125, TaeguTec TT5100, Seco TP2000, Tungaloy T9025, Kennametal KCP25, Ceratizit CTCP115, Ceratizit CTCP125, ISCAR IC9250. This is chart comparability, not verified cutting performance. Grades that share only the ISO position are listed separately as not verified. Same position is not the same performance: verify on a sample part before switching.

Does this cross-reference favour specific brands?

No. Comparable grades appear here only because manufacturer-published comparison charts place them at the same ISO application position. No manufacturer pays for placement, nothing on this page is sponsored, and CuttingToolsAI sells no tools and earns no commission. Placements backed by a single chart are flagged as such, and every comparison ends the same way: verify on a sample part before switching.

Grade charts by brand

Ask the AI advisor about GC4325
Cutting data for your material, when GC4325 is the right call versus its equivalents, and what to check before switching — answered with verified reference data plus live search. Edit the question and hit Ask — 3 free answers a day, no account.
Cost check · free · brand-neutral

Are you overpaying on your GC4325 inserts? Paste your insert list and get a cost audit in about 30 seconds: cross-brand candidate alternatives at the same ISO application position, and where you are likely overpaying. No signup, no sales call.

Run a free cost audit → Check your whole grade list · free

After the free check: a sourced PDF + XLSX report from EUR 9 for one grade. How buying works

Related grades

Where GC4325 is used: designations and materials