Carbide grade · Sandvik · ISO P
Sandvik GC4340
GC4340 is a Sandvik carbide insert grade (Coated), applied in the ISO P area. Its ISO position comes from the manufacturer grade comparison charts in this reference. No manufacturer chart on file lists a direct peer for it. 156 grades from other makers share an ISO position with it. None has been verified. Same position is not the same performance: verify on a sample part before switching.
Grade summary
- Brand
- Sandvik
- Coating / substrate
- Coated
- ISO application area
- P — steel
- ISO position (manufacturer charts)
- P20 · P30
Cross-brand alternatives (manufacturer charts)
Direct peers
Listed in the same row of a manufacturer comparison chart. This is chart comparability, not verified cutting performance.
No manufacturer chart on file lists a direct peer for this grade. Grades at the same ISO position are listed as not verified.
Same ISO position, not verified
These grades overlap in ISO position only. No manufacturer chart lists them together, and operation and tool material are not verified.
- Mitsubishi VP15TF ISO P20 P30 · not verified · carbide
- Sumitomo T2500Z ISO P20 P30 · not verified · cermet
- Tungaloy NS9530 ISO P20 P30 · not verified
- ISCAR IC30N ISO P20 P30 · not verified
- Kennametal KC525M ISO P20 P30 · not verified
106 more not shown.
Tougher alternatives
Positioned above this grade on the ISO scale (more toughness, less wear resistance). ISO position only, not verified.
- ISCAR IC8350 ISO P30 · not verified
- Kyocera PR1535 ISO P30 · not verified · carbide
- Tungaloy UX30 ISO P30 · not verified
- ISCAR IC50M ISO P30 · not verified
- Kennametal KCP30B ISO P30 · not verified
20 more not shown.
More wear-resistant alternatives
Positioned below this grade on the ISO scale (more wear resistance, less toughness). ISO position only, not verified.
- Kyocera PV720 ISO P20 · not verified · cermet
- Kyocera TN620 ISO P20 · not verified · cermet
- Mitsubishi NX2525 ISO P20 · not verified · cermet
- NTK DM4 ISO P20 · not verified
- Sumitomo T1500A ISO P20 · not verified · cermet
15 more not shown.
The best-evidenced alternative to Sandvik GC4340 from another maker, with published cutting speeds (sourced, and compared only where both makers publish them for the same conditions), coating and what would decide a switch. Usually in your inbox within 30 minutes.
Check Sandvik GC4340 against the published chart evidence first. If this grade has a documented candidate, you can order an automatically generated report for one grade (about US$10, charged EUR 9), or add up to two grades (about US$24, charged EUR 22). Currency conversion and tax at checkout may change the USD amount. A chart comparison is not a guaranteed substitute.
Check this grade and see the report →Compare GC4340 side by side
Frequently asked questions
What is Sandvik GC4340?
GC4340 is a Sandvik carbide insert grade (Coated), applied in the ISO P area, as positioned in manufacturer grade charts.
Does this cross-reference favour specific brands?
No. Comparable grades appear here only because manufacturer-published comparison charts place them at the same ISO application position. No manufacturer pays for placement, nothing on this page is sponsored, and CuttingToolsAI sells no tools and earns no commission. Placements backed by a single chart are flagged as such, and every comparison ends the same way: verify on a sample part before switching.
Grade charts by brand
Are you overpaying on your GC4340 inserts? Paste your insert list and get a cost audit in about 30 seconds: cross-brand candidate alternatives at the same ISO application position, and where you are likely overpaying. No signup, no sales call.
After the free check: a sourced PDF + XLSX report from EUR 9 for one grade. How buying works
Related grades
Where GC4340 is used: designations and materials