Carbide grade · Mitsubishi · ISO P
Mitsubishi MC6035
MC6035 is a Mitsubishi carbide insert grade (CVD Al₂O₃), applied in the ISO P area. In this cross-reference it appears on 1 insert designation; the same insert geometry is also made by ISCAR, Kennametal, Sandvik, Seco, Tungaloy, Walter. 5 grades from other makers are confirmed at the same ISO position by two or more manufacturer charts. Same position is not the same performance: verify on a sample part before switching.
Verified cross-brand equivalents for Mitsubishi MC6035, with the manufacturer charts behind each match: Mitsubishi MC6035 equivalents.
Newer grade listed by the maker
Mitsubishi lists Mitsubishi MC6135 against MC6035 in its own documents. That is a maker-stated successor, not a discontinuation notice: see the source and what to check before switching →
Grade summary
- Brand
- Mitsubishi
- Coating / substrate
- CVD Al₂O₃
- ISO application area
- P — steel
- Application range (catalog)
- P30–P40
- Used in
- 1 insert designation in this reference
Cross-brand equivalents (manufacturer charts)
| Brand | Grade | Shared ISO positions | Status |
|---|---|---|---|
| ISCAR | IC9350 | P30 P35 P40 | Confirmed (2+ charts) |
| Kyocera | CA530 | P30 P35 P40 | Confirmed (2+ charts) |
| MOLDINO | IP3000 | P30 P35 P40 | Confirmed (2+ charts) |
| Sandvik | GC4335 | P30 P35 P40 | Confirmed (2+ charts) |
| Seco | TP3501 | P30 P35 P40 | Confirmed (2+ charts) |
| Kyocera | PV730 | P30 | Lead (one chart or partial overlap), not a recommendation |
| Kennametal | KC530M | P30 | Lead (one chart or partial overlap), not a recommendation |
| Kennametal | KCPK30 | P30 | Lead (one chart or partial overlap), not a recommendation |
| Kyocera | PR1230 | P30 | Lead (one chart or partial overlap), not a recommendation |
| MOLDINO | CH7035 | P30 | Lead (one chart or partial overlap), not a recommendation |
The best-evidenced alternative to Mitsubishi MC6035 from another maker, with published cutting speeds (sourced, and compared only where both makers publish them for the same conditions), coating and what would decide a switch. Usually in your inbox within 30 minutes.
Mitsubishi MC6035 plus up to two grades you run next to it, worked through in one document: every cross-brand match with the number of manufacturer charts behind it, single-source candidates kept apart, where your grades overlap so the list can be shortened, and a validation plan. Emailed to you, usually within the hour. No account needed.
Same insert geometry, other brands
These makers produce the same insert designation in their own grade. Shared geometry is not a grade equivalence.
| Brand | Grade | Coating | Shared designations |
|---|---|---|---|
| ISCAR | IC8350 | SUMO TEC® CVD Al₂O₃ | CNMG120412 |
| Kennametal | KCP30B | KENGold™ CVD | CNMG120412 |
| Sandvik | GC4335 | Inveio® CVD | CNMG120412 |
| Seco | TP3500 | Duratomic® CVD | CNMG120412 |
| Tungaloy | T9235 | CVD TiCN/Al₂O₃ | CNMG120412 |
| Walter | WPP30S | Tiger·tec® Silver CVD | CNMG120412 |
Compare MC6035 side by side
Insert designations using MC6035
| Designation | Geometry | Catalog code | Application |
|---|---|---|---|
| CNMG120412 | 80° Diamond · 0° clearance · 12mm IC · 1.2mm Rε · heavy roughing | CNMG120412 MC6035 | P30–P40 |
Frequently asked questions
What is Mitsubishi MC6035?
MC6035 is a Mitsubishi carbide insert grade (CVD Al₂O₃), applied in the ISO P area, used in 1 insert designation in this reference.
Which grades are comparable to MC6035?
Grades from other makers confirmed at the same ISO application position by two or more manufacturer charts include ISCAR IC9350, Kyocera CA530, MOLDINO IP3000, Sandvik GC4335, Seco TP3501. Same position is not the same performance: treat them as starting points and verify on a sample part before switching.
Does this cross-reference favour specific brands?
No. Comparable grades appear here only because manufacturer-published comparison charts place them at the same ISO application position. No manufacturer pays for placement, nothing on this page is sponsored, and CuttingToolsAI sells no tools and earns no commission. Placements backed by a single chart are flagged as such, and every comparison ends the same way: verify on a sample part before switching.
Grade charts by brand
Are you overpaying on your MC6035 inserts? Paste your insert list and get a cost audit in about 30 seconds: cross-brand equivalents at the same ISO application position, and where you are likely overpaying. No signup, no sales call.
Related grades
Where MC6035 is used: designations and materials