CUTTINGTOOLS / AI
Find equivalents

Carbide grade · ISCAR · ISO P

ISCAR IC8350

IC8350 is a ISCAR carbide insert grade (SUMO TEC® CVD Al₂O₃), applied in the ISO P area. In this cross-reference it appears on 1 insert designation; the same insert geometry is also made by Kennametal, Mitsubishi, Sandvik, Seco, Tungaloy, Walter. 1 Direct peer is from other makers, listed in the same row of a manufacturer comparison chart. This is chart comparability, not verified cutting performance. 84 more grades share an ISO position only and are not verified. Same position is not the same performance: verify on a sample part before switching.

Same ISO position in the manufacturer charts, with the source on the full page. Running several grades? Separate them with commas to check the whole list. No signup.

Every maker's AI recommends its own tools. Ours compares all makers and shows the published source behind each answer, or tells you it could not verify.

Grade summary

Brand
ISCAR
Coating / substrate
SUMO TEC® CVD Al₂O₃
ISO application area
P — steel
Application range (catalog)
P30–P40
Used in
1 insert designation in this reference

Cross-brand alternatives (manufacturer charts)

Direct peers

Listed in the same row of a manufacturer comparison chart. This is chart comparability, not verified cutting performance.

  • Sandvik GC4335 ISO P30 P35 · 3 charts (Ingersoll, TaeguTec, Tungaloy)

Same ISO position, not verified

These grades overlap in ISO position only. No manufacturer chart lists them together, and operation and tool material are not verified.

  • Kyocera PR1535 ISO P30 P35 · not verified · carbide
  • Mitsubishi VP20RT ISO P30 P35 · not verified
  • Tungaloy UX30 ISO P30 P35 · not verified
  • Mitsubishi UTi20T ISO P30 P35 · not verified
  • Kyocera PV730 ISO P30 · not verified · cermet

55 more not shown.

More wear-resistant alternatives

Positioned below this grade on the ISO scale (more wear resistance, less toughness). ISO position only, not verified.

19 more not shown.

Check IC8350 with your other grades →

Free · engineer's note · by email

The best-evidenced alternative to ISCAR IC8350 from another maker, with published cutting speeds (sourced, and compared only where both makers publish them for the same conditions), coating and what would decide a switch. Usually in your inbox within 30 minutes.

Source-backed grade report · PDF + XLSX

Check ISCAR IC8350 against the published chart evidence first. If this grade has a documented candidate, you can order an automatically generated report for one grade (about US$10, charged EUR 9), or add up to two grades (about US$24, charged EUR 22). Currency conversion and tax at checkout may change the USD amount. A chart comparison is not a guaranteed substitute.

Check this grade and see the report →

Same insert geometry, other brands

These makers produce the same insert designation in their own grade. Shared geometry is not a grade equivalence.

BrandGradeCoatingShared designations
Kennametal KCP30B KENGold™ CVD CNMG120412
Mitsubishi MC6035 CVD Al₂O₃ CNMG120412
Sandvik GC4335 Inveio® CVD CNMG120412
Seco TP3500 Duratomic® CVD CNMG120412
Tungaloy T9235 CVD TiCN/Al₂O₃ CNMG120412
Walter WPP30S Tiger·tec® Silver CVD CNMG120412

Insert designations using IC8350

DesignationGeometryCatalog codeApplication
CNMG120412 80° Diamond · 0° clearance · 12mm IC · 1.2mm Rε · heavy roughing CNMG120412 IC8350 P30–P40

Frequently asked questions

What is ISCAR IC8350?

IC8350 is a ISCAR carbide insert grade (SUMO TEC® CVD Al₂O₃), applied in the ISO P area, used in 1 insert designation in this reference.

Which grades are direct peers of IC8350?

1 grade from another maker is listed in the same row of a manufacturer comparison chart as IC8350: Sandvik GC4335. This is chart comparability, not verified cutting performance. Grades that share only the ISO position are listed separately as not verified. Same position is not the same performance: verify on a sample part before switching.

Does this cross-reference favour specific brands?

No. Comparable grades appear here only because manufacturer-published comparison charts place them at the same ISO application position. No manufacturer pays for placement, nothing on this page is sponsored, and CuttingToolsAI sells no tools and earns no commission. Placements backed by a single chart are flagged as such, and every comparison ends the same way: verify on a sample part before switching.

Grade charts by brand

Ask the AI advisor about IC8350
Cutting data for your material, when IC8350 is the right call versus its equivalents, and what to check before switching — answered with verified reference data plus live search. Edit the question and hit Ask — 3 free answers a day, no account.
Cost check · free · brand-neutral

Are you overpaying on your IC8350 inserts? Paste your insert list and get a cost audit in about 30 seconds: cross-brand candidate alternatives at the same ISO application position, and where you are likely overpaying. No signup, no sales call.

Run a free cost audit → Check your whole grade list · free

After the free check: a sourced PDF + XLSX report from EUR 9 for one grade. How buying works

Related grades

Where IC8350 is used: designations and materials