CUTTINGTOOLS / AI
Find equivalents

Carbide grade · ISCAR · ISO M/S

ISCAR IC806

IC806 is a ISCAR carbide insert grade (PVD TiAlN (SUMO TEC®)), applied in the ISO M/S areas. In this cross-reference it appears on 1 insert designation; the same insert geometry is also made by Kennametal, Tungaloy. 1 Direct peer is from other makers, listed in the same row of a manufacturer comparison chart. This is chart comparability, not verified cutting performance. 33 more grades share an ISO position only and are not verified. Same position is not the same performance: verify on a sample part before switching.

Candidate cross-brand alternatives for ISCAR IC806, with the manufacturer charts behind each one: ISCAR IC806 equivalents.

Same ISO position in the manufacturer charts, with the source on the full page. Running several grades? Separate them with commas to check the whole list. No signup.

Every maker's AI recommends its own tools. Ours compares all makers and shows the published source behind each answer, or tells you it could not verify.

Grade summary

Brand
ISCAR
Coating / substrate
PVD TiAlN (SUMO TEC®)
ISO application area
M — stainless steel · S — superalloys & titanium
Application range (catalog)
S15–S25
Used in
1 insert designation in this reference

Cross-brand alternatives (manufacturer charts)

Direct peers

Listed in the same row of a manufacturer comparison chart. This is chart comparability, not verified cutting performance.

  • Sandvik GC1115 ISO S10 · 1 chart (Ingersoll)

Same ISO position, not verified

These grades overlap in ISO position only. No manufacturer chart lists them together, and operation and tool material are not verified.

  • Sandvik GC1105 ISO S05 S10 · not verified
  • Walter WSM01 ISO S05 S10 · not verified
  • Tungaloy TH10 ISO S10 · not verified
  • Seco TH1500 ISO S10 · not verified
  • Tungaloy KS05F ISO S05 S10 · not verified

25 more not shown.

Tougher alternatives

Positioned above this grade on the ISO scale (more toughness, less wear resistance). ISO position only, not verified.

  • Tungaloy AH120 ISO S10 · not verified
  • Seco CP200 ISO S10 · not verified
  • TaeguTec TT3020 ISO S10 · not verified

Check IC806 with your other grades →

Free · engineer's note · by email

The best-evidenced alternative to ISCAR IC806 from another maker, with published cutting speeds (sourced, and compared only where both makers publish them for the same conditions), coating and what would decide a switch. Usually in your inbox within 30 minutes.

Source-backed grade report · PDF + XLSX

Check ISCAR IC806 against the published chart evidence first. If this grade has a documented candidate, you can order an automatically generated report for one grade (about US$10, charged EUR 9), or add up to two grades (about US$24, charged EUR 22). Currency conversion and tax at checkout may change the USD amount. A chart comparison is not a guaranteed substitute.

Check this grade and see the report →

Same insert geometry, other brands

These makers produce the same insert designation in their own grade. Shared geometry is not a grade equivalence.

BrandGradeCoatingShared designations
Kennametal KCU10B PVD AlTiN RCMT1204
Tungaloy AH8015 PVD AlTiN RCMT1204

Insert designations using IC806

DesignationGeometryCatalog codeApplication
RCMT1204 Round · 7° clearance · 12mm diameter · 4.76mm thick RCMT 1204M0-14 IC806 S15–S25

Frequently asked questions

What is ISCAR IC806?

IC806 is a ISCAR carbide insert grade (PVD TiAlN (SUMO TEC®)), applied in the ISO M/S areas, used in 1 insert designation in this reference.

Which grades are direct peers of IC806?

1 grade from another maker is listed in the same row of a manufacturer comparison chart as IC806: Sandvik GC1115. This is chart comparability, not verified cutting performance. Grades that share only the ISO position are listed separately as not verified. Same position is not the same performance: verify on a sample part before switching.

Does this cross-reference favour specific brands?

No. Comparable grades appear here only because manufacturer-published comparison charts place them at the same ISO application position. No manufacturer pays for placement, nothing on this page is sponsored, and CuttingToolsAI sells no tools and earns no commission. Placements backed by a single chart are flagged as such, and every comparison ends the same way: verify on a sample part before switching.

Grade charts by brand

Ask the AI advisor about IC806
Cutting data for your material, when IC806 is the right call versus its equivalents, and what to check before switching — answered with verified reference data plus live search. Edit the question and hit Ask — 3 free answers a day, no account.
Cost check · free · brand-neutral

Are you overpaying on your IC806 inserts? Paste your insert list and get a cost audit in about 30 seconds: cross-brand candidate alternatives at the same ISO application position, and where you are likely overpaying. No signup, no sales call.

Run a free cost audit → Check your whole grade list · free

After the free check: a sourced PDF + XLSX report from EUR 9 for one grade. How buying works

Related grades

Where IC806 is used: designations and materials