Carbide grade · ISCAR · ISO P
ISCAR IC8150
IC8150 is a ISCAR carbide insert grade (SUMO TEC® CVD Al₂O₃), applied in the ISO P area. In this cross-reference it appears on 11 insert designations; the same insert geometry is also made by Kennametal, Mitsubishi, Sandvik, Seco, Tungaloy, Walter. 5 grades from other makers are confirmed at the same ISO position by two or more manufacturer charts. Same position is not the same performance: verify on a sample part before switching.
Grade summary
- Brand
- ISCAR
- Coating / substrate
- SUMO TEC® CVD Al₂O₃
- ISO application area
- P — steel
- Application range (catalog)
- P10–P20
- Used in
- 11 insert designations in this reference
Cross-brand equivalents (manufacturer charts)
| Brand | Grade | Shared ISO positions | Status |
|---|---|---|---|
| MOLDINO | HG8010 | P05 P15 | Confirmed (2+ charts) |
| Kennametal | KCP05 | P05 | Confirmed (2+ charts) |
| Kyocera | CA510 | P05 | Confirmed (2+ charts) |
| Kyocera | CA5505 | P05 | Confirmed (2+ charts) |
| Mitsubishi | UE6105 | P05 | Confirmed (2+ charts) |
| Mitsubishi | MC6115 | P05 P15 | Lead (one chart or partial overlap), not a recommendation |
| Sumitomo | AC8015P | P05 P15 | Lead (one chart or partial overlap), not a recommendation |
| Kennametal | KC5010 | P15 | Lead (one chart or partial overlap), not a recommendation |
| Kennametal | KC510M | P05 | Lead (one chart or partial overlap), not a recommendation |
| Kennametal | KCP05B | P05 | Lead (one chart or partial overlap), not a recommendation |
ISCAR IC8150 plus up to two grades you run next to it, worked through in one document: every cross-brand match with the number of manufacturer charts behind it, single-source candidates kept apart, where your grades overlap so the list can be shortened, and a validation plan. Emailed to you, usually within the hour. No account needed.
Same insert geometry, other brands
These makers produce the same insert designation in their own grade. Shared geometry is not a grade equivalence.
Compare IC8150 side by side
Insert designations using IC8150
| Designation | Geometry | Catalog code | Application |
|---|---|---|---|
| CCMT09T304 | 80° Diamond · 7° clearance (positive) · precision finishing | CCMT09T304 IC8150 | P10–P20 |
| CCMT09T308 | 80° Diamond · 7° clearance (positive) · 0.8mm Rε | CCMT09T308 IC8150 | P10–P20 |
| DCMT11T304 | 55° Diamond · 7° clearance (positive) · 0.4mm Rε | DCMT11T304 IC8150 | P10–P20 |
| TCMT16T304 | 60° Triangle · 7° clearance (positive) · 0.4mm Rε | TCMT16T304 IC8150 | P10–P20 |
| TNMG160404 | 60° Triangle · 0° clearance · 16mm IC · 0.4mm Rε · semi-finishing | TNMG160404 IC8150 | P10–P20 |
| VBMT160404 | 35° Rhombic · 5° clearance · 16mm IC · 0.4mm Rε · tight corner finishing | VBMT160404 IC8150 | P10–P20 |
| VBMT160408 | 35° Rhombic · 5° clearance · 16mm IC · 0.8mm Rε | VBMT160408 IC8150 | P10–P20 |
| WNMG060408 | 80° Trigon · 0° clearance · 6mm IC · 0.8mm Rε · small diameter turning | WNMG060408 IC8150 | P10–P20 |
| WNMG080404 | 80° Trigon · 0° clearance · 8mm IC · 0.4mm Rε (finishing) | WNMG080404 IC8150 | P10–P20 |
| WNMG080408 | 80° Trigon · 0° clearance · 8mm IC · 0.8mm Rε | WNMG080408 IC8150 | P10–P20 |
| WNMG080412 | 80° Trigon · 0° clearance · 8mm IC · 1.2mm Rε (roughing) | WNMG080412 IC8150 | P10–P20 |
Frequently asked questions
What is ISCAR IC8150?
IC8150 is a ISCAR carbide insert grade (SUMO TEC® CVD Al₂O₃), applied in the ISO P area, used in 11 insert designations in this reference.
Which grades are comparable to IC8150?
Grades from other makers confirmed at the same ISO application position by two or more manufacturer charts include MOLDINO HG8010, Kennametal KCP05, Kyocera CA510, Kyocera CA5505, Mitsubishi UE6105. Same position is not the same performance: treat them as starting points and verify on a sample part before switching.
Does this cross-reference favour specific brands?
No. Comparable grades appear here only because manufacturer-published comparison charts place them at the same ISO application position. No manufacturer pays for placement, nothing on this page is sponsored, and CuttingToolsAI sells no tools and earns no commission. Placements backed by a single chart are flagged as such, and every comparison ends the same way: verify on a sample part before switching.
Grade charts by brand
Are you overpaying on your IC8150 inserts? Paste your insert list and get a cost audit in about 30 seconds: cross-brand equivalents at the same ISO application position, and where you are likely overpaying. No signup, no sales call.
Related grades