Carbide grade · Tungaloy · ISO P/M
Tungaloy T9115
T9115 is a Tungaloy carbide insert grade (CVD TiCN/Al₂O₃), applied in the ISO P/M areas. In this cross-reference it appears on 11 insert designations; the same insert geometry is also made by ISCAR, Kennametal, Mitsubishi, Sandvik, Seco, Walter. A reference record exists, but its evidence is not approved for service. Same position is not the same performance: verify on a sample part before switching.
Grade summary
- Brand
- Tungaloy
- Coating / substrate
- CVD TiCN/Al₂O₃
- ISO application area
- P — steel · M — stainless steel
- Application range (catalog)
- P10–P20
- Used in
- 11 insert designations in this reference
Cross-brand equivalents (manufacturer charts)
A reference record exists, but its evidence is not approved for service.
Same insert geometry, other brands
These makers produce the same insert designation in their own grade. Shared geometry is not a grade equivalence.
Insert designations using T9115
| Designation | Geometry | Catalog code | Application |
|---|---|---|---|
| CCMT09T304 | 80° Diamond · 7° clearance (positive) · precision finishing | CCMT09T304 T9115 | P10–P20 |
| CCMT09T308 | 80° Diamond · 7° clearance (positive) · 0.8mm Rε | CCMT09T308 T9115 | P10–P20 |
| DCMT11T304 | 55° Diamond · 7° clearance (positive) · 0.4mm Rε | DCMT11T304 T9115 | P10–P20 |
| TCMT16T304 | 60° Triangle · 7° clearance (positive) · 0.4mm Rε | TCMT16T304 T9115 | P10–P20 |
| TNMG160404 | 60° Triangle · 0° clearance · 16mm IC · 0.4mm Rε · semi-finishing | TNMG160404 T9115 | P10–P20 |
| VBMT160404 | 35° Rhombic · 5° clearance · 16mm IC · 0.4mm Rε · tight corner finishing | VBMT160404 T9115 | P10–P20 |
| VBMT160408 | 35° Rhombic · 5° clearance · 16mm IC · 0.8mm Rε | VBMT160408 T9115 | P10–P20 |
| WNMG060408 | 80° Trigon · 0° clearance · 6mm IC · 0.8mm Rε · small diameter turning | WNMG060408 T9115 | P10–P20 |
| WNMG080404 | 80° Trigon · 0° clearance · 8mm IC · 0.4mm Rε (finishing) | WNMG080404 T9115 | P10–P20 |
| WNMG080408 | 80° Trigon · 0° clearance · 8mm IC · 0.8mm Rε | WNMG080408 T9115 | P10–P20 |
| WNMG080412 | 80° Trigon · 0° clearance · 8mm IC · 1.2mm Rε (roughing) | WNMG080412 T9115 | P10–P20 |
Frequently asked questions
What is Tungaloy T9115?
T9115 is a Tungaloy carbide insert grade (CVD TiCN/Al₂O₃), applied in the ISO P/M areas, used in 11 insert designations in this reference.
Does this cross-reference favour specific brands?
No. Comparable grades appear here only because manufacturer-published comparison charts place them at the same ISO application position. No manufacturer pays for placement, nothing on this page is sponsored, and CuttingToolsAI sells no tools and earns no commission. Placements backed by a single chart are flagged as such, and every comparison ends the same way: verify on a sample part before switching.
Grade charts by brand
Are you overpaying on your T9115 inserts? Paste your insert list and get a cost audit in about 30 seconds: cross-brand equivalents at the same ISO application position, and where you are likely overpaying. No signup, no sales call.
Related grades